[3-150W LED & 3-300W halogen (pack of 2)]
[3-150W LED & 3-300W halogen]
1 x iolloi LED dimmer 150 W1, middle frame, outer frame, rotary knob, 1 x washer and nut, metal seal, 1 x 6 mm adapter and adapter washer, 1 x German user manual
|
|
|
---|---|---|
How do I choose bulbs?1. Please make sure your bulb is dimmable. 2. Make sure your bulb uses a phase control lighting solution. 3. We have suggested bulb brand: Philips, Osram, AmazonBasics, Cree and other bulb brands. |
Does it work and is it safe?1. Normal operation of the dimmer requires the bulb to be dimmed. 2. The dimming range supported by this dimmer is 0-100, and there is no noise and no flickering. 3. This dimmer is protected against overload, overheating and peak voltage. 4.Not suitable for motors, fans and ring core transformers. |
How can I be compatible with other panels?1. If you use iolloi, Gira and Berker panels, you do not need to use a metal seal and 6 mm adapter. 2. If you use a Busch Hunter panel, you will need to use the 6mm adapter included in the accessories. 3. If you use a young panel, you need to use the adapter seal and some models need to use metal seals. |
Since this product has no claws, it requires a standard embedded mounting box to install it normally. In addition, you need two screws to tighten the product. Always make sure that the power supply is completely switched off during installation. If in doubt about the installation, please contact a qualified electrician.
The 1-way installation is suitable for scenarios where only dimmers are used and no two-way switches are required. L = live cable, plug the live wire into this port and tighten it with a screwdriver. Load logo = load, insert the load wire that connects the bulb into the load port and tighten it with a screwdriver. More than a dimmer cannot be parallel or in. Series are switched between between between the same load from two different locations.
2-way installation, can be dimmed in one place, switched on and off in another place. L = live cable, plug the live wire into this port and tighten it with a screwdriver. L2 = Live Line 2, plug the wire into the on/off switch into the L2 connector and tighten with a screwdriver. Load logo = load, run the load wire that the bulb. goes in a patch and tighten it with a screwdriver. More than one dimmer cannot be switched parallel or in series to control the same load from two different locations.
VR – Variable resistance clockwise to increase the brightness at the minimum point. Minimum brightness adjustable to avoid flickering or a satisfactory min. Brightness. If the bulb flickers or cannot be dimmed, please make sure that the bulb you use is dimmable, and support the phase control dimming
Normal flush-mounted boxes
1-way installation
2-way installation
Minimum brightness set
![]() |
![]() |
![]() |
![]() |
![]() |
|
---|---|---|---|---|---|
LED dimmer | LED dimmer with clamping claws | Universal dimmer | Zigbee LED dimmer | Zigbee LED dimmer | |
Customer Reviews |
4.2 out of 5 stars
2,481
|
4.0 out of 5 stars
3,310
|
4.2 out of 5 stars
2,481
|
4.3 out of 5 stars
458
|
4.1 out of 5 stars
618
|
Price | USD 21.75USD21.75 | USD 34.79USD34.79 | — | USD 46.22USD46.22 | USD 32.63USD32.63 |
Output power: | 3-150 W (LED) | 3-300 W (LED) | 3-300 W (LED) | 5-200 W (LED) | 5-200 W (LED) |
Brightness limit | Min | Min/Max | Min | Min | Min |
Double-way circuits | ✓ | ✓ | ✓ | ✓ | ✓ |
Overload protection, over current protection, over temperature protection | ✓ | ✓ | ✓ | ✓ | ✓ |
Adapter for 6 mm rotary axles | ✓ | ✓ | ✓ | ✓ | |
Dimming mode | Phase section | Phase section | Phase control / phase control | Phase section | Phase section |
Dimensions: | 84 x 84 x 45 mm | 84 x 84 x 45 mm | 84 x 84 x 45 mm | 84 x 84 x 45 mm | 46 x 45.5 x 19.8 mm |