Feature(may vary by option.)
●✔️ Compatible with the Bosch drives Performance Line CX Gen5 Smart System with Kiox 300/500 | Purion 200 | Intuvia 100 | LED/Mini Remote | System Controller
●✔️ Speed limit of 25 km/h can be adjusted
●✔️ The actual speed and average speed remain readable, maximum speed, distance kilometres and total kilometres are displayed correctly
●✔️ Easy installation. Custom fit connectors Lediglich ein Stecker muss gezogen und der sIMPLEk zwischgeschaltet werden
●✔️ Not visible from the outside. In the standard configuration, the e-bike always starts with deactivated tuning without any intervention
●Not compatible with the internal speed sensor (recognisable by magnet on the rear valve) and the ABS system
[Stealth Edition]
[Nano Edition]
Description
simplek Pro tuning module for Bosch Smart System (Nano Edition)
Compatible with the Performance Line (CX) Smart System motor with conventional speed sensor (no magnet on the rear wheel valve). Speed limit for the engine support can be set via menu. The actual speed remains readable, average speed, maximum speed, distance kilometres and total. kilometometometometometometre Displayed¹Stealth mode to reduce error messages is integrated and can be activated/disabled
Easy installation thanks to the precise waterproof connector. These are made in high-quality 3D printing process. Thus, the module can be easily installed and removed without leaving a trace. Not visible from the outside. In the standard configuration, the e-bike always starts with deactivated tuning without intervention
______________________________
¹The actual speed is displayed correctly via the second digit and decimal place of the speed display when the speed limit is not lowered. In case of reduced speed limits, values must be subtracted. The average speed is displayed briefly when activated with each hold. The maximum speed and the track indicators are displayed after approx. one minute at a standstill.
The operation of the sIMPLEk Pro within the scope or Effective range of the German Road Traffic Regulations is prohibited and not permitted
The speed remains readable in tuning mode¹:
If the speed limit is not reduced in normal mode and stealth mode, the speed remains readable over the entire range. Up to 22 km/h, the speed is normally output. Above 22 km/h, it is displayed via the second digit and the decimal place. As a result, the average speed in the display always remains in the inconspicuous realistic range. This trick has been in use with our modules for over 5 years and has proven itself well. Examples:
Displayed 22.9 km/h corresponds to 29 km/h. Displayed 23.4 km/h corresponds to 34 km/h. Displayed 24.2 km/h corresponds to 42 km/h
The current average speed is displayed briefly after each stop (when activated). The distance kilometres travelled are automatically restored after one minute in a stop (if not deactivated). This means that maximum speed, distance and total kilometres are correct at the end of the tour.
The throttle with the module extends over a range of approx. 7 km/h. This allows support even at high speeds, while the risk of tuning detection remains low. In addition, this protects battery consumption.
For this purpose, a one-time simple calibration is necessary, which automatically starts at the first startup: The speedometer shows an increasing speed. Once the desired calibration value is displayed, the ebike must be switched off and then switched on again. Now a speed increasing in small steps is displayed on the speedometer and it must be switched off again at the exact desired calibration value.
Easy activation and deactivation even while driving:
|
|
|
|
|---|---|---|
|
Turn on e-bike |
Turn off the e-bike after it is completely up |
When switched on again, the tuning mode is active (signals by displayed 10.0 km/h) and remains active until the bike is switched off again. |
The settings menu can be accessed by starting the tuning mode and then waiting for the displayed 10 km/h to jump to 11 km/h after about 15 seconds. Then the individual menu items listed can be selected by generating sensor signals (turn the rear wheel). The selection is confirmed by turning off the bike when the menu item is selected. The menu can be cancelled at any time by driving off.
Speed limit for engine support can be adjusted:
After selecting the menu point 12 (speed limit for engine support), a falling speed is displayed when switched on again starting from the current setting value. One sensor pulse changes direction (rising/falling), two sensor pulses confirm the selection for the current displayed speed (the decimal point is not considered). If the e-bike is switched off within 10 seconds after selection, the value is permanently saved, otherwise the setting only applies to the current ride.
Compatible with the Smart System engines Performance Line (CX) and the Kiox 300 display