Feature(may vary by option.)
●Specifications: With a pressure resistance of 0.1 - 10 bar and a temperature range of -10 to 120°C, the valve is suitable for most applications. The normal open valve has a 1/2 inch thread connection and is operated with AC 220V ±10%.
●Precise control: the electric solenoid valve can be perfectly adjusted to the desired parameters thanks to the precise mechanism. You will receive exactly the flow rate you need without fluctuations.
●High quality: for our U.S Solid 230 V solenoid valve, we use sturdy brass, which in combination with the Viton seal ensures a special durability. The seal can withstand very high temperatures and is resistant to chemicals with optimal sealing.
●✅ NOTES: The valve must be installed horizontally, the arrow indicates the direction of the flow direction. To ensure a long service life, the solenoid valve should not be operated for more than 8 hours.
●Versatile: the electric valve can be used in a wide range of areas such as home, commercial and medicine. Thanks to the special properties, a perfect adjustment of the flow rate is achieved.
[Brass 1 ]
[Brass 3 & 4 ]
[Stainless Steel 1 ]
[Brass 1 & 2 ]
Description
|
|
|
|
|---|---|---|
About IP65 RatingThe solenoid valves have an IP65 rating, which means they can withstand spray from water. However, if permanently installed outdoors, it is recommended that you enclose the valves in some protective housing. They are not meant for use underwater. |
About Operating PressureAll solenoid valves require a minimum pressure to actuate. These semi-direct operated valves require at least 0.1 bar. The maximum pressure is 10 bar. |
About Filter InstallationTo prevent issues with the valve, we recommend installing a filter if there are particles in the water. If the valve cannot be fully closed or opened, it is usually due to impurities inside the valve. In that case, you will need to open the valve and clean the internal parts. |
|
|
|
|
|---|---|---|
About Flow DirectionPlease note that an arrow indicating the installation or flow direction can be found at the bottom of the solenoid valve. You must install the solenoid valve only in the specified flow direction. Installing it in the opposite direction will prevent the solenoid valve from working properly. |
About ConnectionsType 1 Connection: Prepare cables with a minimum cross-sectional area of 0.75 mm2 and an outer diameter of 7-9 mm. Connect the cables to the pins through the side connector. Type 2 Connection: Remove the side connector and connect the pins directly to the terminal. The left and right pins can be L(+) or N(-). The middle pin is connected to protective earth/ground. |
About Duty CyclesIt is normal for solenoid valves to heat up significantly after prolonged operation (up to approx. 80°C).Do not worry, our coil can withstand a maximum temperature of 180°C. This valve supports 100% continuous duty operation, but we do not recommend continuous use. Because doing so will shorten the valves life and may burn out the coil. |
|
|
|
|
|
|
|
|---|---|---|---|---|---|---|
| JFYSV00003-G | JFYSV00006-G | JFYSV00010-G | JFYSV00024-G | JFYSV00016-G | JFYSV00023-G | |
| Port Size | 1/2" | 1/2" | 1/2" | 1/2" | 1/2" | 1/2" |
| Rated voltage | 220V AC ± 10% | 24V AC, ± 10% | 12V DC, ± 10% | 24V DC, ± 10% | 220V AC ± 10% | 220V AC ± 10% |
| Body Material | Brass | Brass | Brass | Brass | Stainless Steel | Brass |
| Operating mode | NC | NC | NC | NC | NC | NO |