Feature
●The TWP 7025 E dirty water submersible pump transports heavily contaminated water with particles of up to 25 mm in size.
●The high-quality ceramic sliding ring seal and a low-wear shaft increase the life of the pump.
●The float can be attached as desired, thus increasing the flexibility when adjusting the switching point on and off. Furthermore, it protects against dry running.
●With the horizontal locking of the float switch, the pump runs in continuous operation and sucks the water up to 35 mm.
●To let the pump into the water, the included 12 metre long nylon rope is attached to the sturdy ergonomic carrying handle.
Description
The TWP 7025 E dirty water submersible pump is a compact powerhouse that masters almost any task. The highly absorbent pump also transports heavily contaminated water, even over floors. Water from home and garden can and should be pumped out as quickly and effectively as possible - and for this task the pump is ideal.
Stays cool even when stressed.
Powerful 750 watt power brings the dirty water submersible pump TWP 7025 E into the go. Even 25 mm large dirt and floating particles can be transported with up to 13,000 litres of clear and dirty water per hour. A discharge height of 9 metres is still no problem despite the high transport performance. It creates a cellar filled after a flooding without any problems - the water can be transported to the next floor higher and then simply drained. But water has not only lost nothing in the cellar, it should not penetrate the device. Due to the IPX8 protection class, the technology inside is safe from the water. And so that nothing can happen during immersion, the waterproof encapsulated plastic housing is also impact-resistant and therefore also protected against impact in walls or currents. In addition to temporary use, continuous use is also possible - the integrated thermal protection circuit protects against overheating. The submersible pump is suitable for underwater use up to 7 metres diving depth. With the pumping of dirty water, the pump can start from a minimum working depth of 115 mm and then works up to a residual water level of 35 mm.
Intuitive operation meets flexibility
The choice of operating mode of the TWP 7025 E is easy and comfortable thanks to the continuously lockable float switch. In automatic operation, the float switch takes care of switching the pump on and off after previous definition of the water level. To ensure that the pump does not run dry, the dry run protection interacts if the water level is too low during operation. If you set the float switch horizontally in a continuous operating position, manual operation in low water level, from 115 mm is also possible. The clear and dirty water submersible pump then continues to work until the device has reached the residual water level with a maximum suction height of 35 mm. On the arbitrarily adjustable angle adapter there are universal connections to which hose or pipe connections with 25 mm and 32 mm inner diameter as well as 1 inch and 1 ½ inch thread connections can be easily connected. The hoses or pipes can be laid parallel to the floor if desired. The power cable with 10 metres in length offers enough room and flexibility. Finally, the ergonomic carrying handle allows mobile application location change - and at the same time serves as a suspension for the included nylon rope to leave the device even in deeper fountains.
High-quality pump for comprehensive work.
In order to protect the technology inside the TWP 7025 E, the housing is made from a sturdy, impact-resistant and, above all, waterproof plastic. The submersible pump is therefore a pleasure in the long run. A ceramic sliding ring seal not only speaks for high quality, it also allows a long service life of the pump - for which the low-wear shaft also ensures in the device. The powerful motor is also long-lasting, which not only protects the housing, but above all is low-maintenance.
The removal of water from lakes, ponds or rivers as well as the pumping and pumping out of basements, swimming pools, small construction pits, rain barrels or flooding makes the pump no problem. Thanks to its high performance, the TWP 7025 E submersible pump is ideal for transporting large amounts of contaminated water. The package consists of the dirty water submersible pump, a reducing adapter, an angle adapter, a 12 m long nylon rope and a 10 m long power cable with CEE 7/4 connector plug.
The technical details at a glance: Maximum flow rate: : 13,000 l/h. Grain: 25 mm discharge head max. : 9 m immersion depth max. : 7 m. Minimum working depth: 115 mm water level suction height max. : 35 mm. Height of switch-on point: 500 mm. Height off point: 250 mm water temperature max. : 35 °C. Input voltage: 230 - 240 V / 50 Hz. Power consumption: 0.75 kW. Dimensions (L x W x H): 220 x 160 x 390 mm. Weight: 5.2 kg.
