●Requires attention: Please measure the distance between the bicycle frame and the floor before purchase (for bicycles with the same frame size, the distance to the floor also varies) to ensure that the height is correct: 19 cm - 26.5 cm (7.4 inches - 10.4 inches). ●For 16-20 inches: this childrens bicycle stand for 16 inch 18 inch 20 inch. Please note that the size 16-20 inches refers to the wheel size and not the size of the bike. Make sure the height of the bicycle frame above the ground is between 19 cm - 26.5 cm (7.4 inches - 10.4 inches) ●Easy installation: the bicycle stand is equipped with two hex screws of different sizes (8 mm/4 mm) to facilitate installation. Stainless steel washers are used in conjunction with the top screws to ensure stability. ●Adjustable height bicycle side stand: the slide rail is equipped with a small hexagon socket screw. Slide rail adjustable by 4 cm in length. This makes it easy to adjust the correct height to ensure sufficient stability. Its easy: loosen the flat head screw, adjust the height and tighten the flat head screw again. ●High-quality materials: the bicycle stand mountain bike offers the highest quality made of high-quality aluminium alloy and stainless steel screws. The bicycle stand has a flat non-slip foot to ensure more resting stability, prevent slipping on wet surfaces and sink into the mud.
Description
Verstellbare Größe
Hochwertiges Material
Wie wähle ich den richtigen Fahrradständer aus?
Folgende 2 Bedingungen müssen erfüllt sein:
Fahrradradgröße Anzeigeposition der Reifengröße Für Reifengrößen von 16/18/20 Zoll
Messen der vertikalen Höhe des Fahrradrahmens 19-26.5cm(7.4-10.4inch)
Video Player is loading.
Current Time 0:00
/
Duration -:-
Loaded: 0%
Stream Type LIVE
Remaining Time -0:00
1x
Chapters
descriptions off, selected
captions off, selected
This is a modal window.
Fahrrad Seitenständer
Fahrrad Seitenständer
Anzeige der Produktdetails
Wie baue ich den Fahrradständer kinderfahrrad zusammen?
Schritt 1: Installieren Sie ohne Kappe
Platzieren Sie den Seitenständer unter dem Metallteil und ziehen Sie die Schraube mit dem 8-mm-Inbusschlüssel fest.
Video Player is loading.
Current Time 0:00
/
Duration 0:09
Loaded: 1.70%
0:00
Stream Type LIVE
Remaining Time -0:09
1x
Chapters
descriptions off, selected
captions off, selected
This is a modal window.
Schritt 2: Installieren Sie mit Cap
Platzieren Sie den Ständer unter dem Metallteil, setzen Sie die Kappe auf das Metallteil und ziehen Sie die Schraube mit dem 8-mm-Inbusschlüssel fest.
Video Player is loading.
Current Time 0:00
/
Duration -:-
Loaded: 0%
Stream Type LIVE
Remaining Time -0:00
1x
Chapters
descriptions off, selected
captions off, selected
This is a modal window.
Passt er auf alle Arten von 16" Fahrrädern?
Kinderfahrräder der gleichen Größe 16 Zoll. Aber aufgrund der unterschiedlichen Konstruktion des Fahrrads.
Daher ist die Höhe des Rahmens über dem Boden unterschiedlich. Dass die Höhe 19-26.5cm(7.4-10.4inch)
Worauf sollte ich vor dem Kauf achten?
Notiz Messungen:Bitte messen Sie vor dem Kauf unbedingt den Abstand zwischen der mittleren Rahmenstange und dem Boden, stellen Sie sicher, dass die Höhe 19-26.5cm(7.4-10.4inch)
Wie kann ich sie besser montieren, damit sie nicht kaputt geht?
Lösen Sie mit dem Sechskantschlüssel die Schraube in der Mitte des Ständers und ziehen Sie die Schraube nach dem Einstellen der richtigen Höhe wieder fest.Stellen Sie bitte sicher, dass alle Schrauben angezogen sind, um zu verhindern.